Clipsal 56011 Spezifikationen PDF herunterladen (Seite 18)

M1 to Leviton Z-Wave Interface

The M1XSLZW is a specialized M1 serial expander for connecting M1 Controls to Z-Wave enabled

devices through a Leviton VRC0P-1LW Z-Wave Serial Interface. Z-Wave is a wireless, low power, “mesh”

network technology widely used for automating devices such as: lights, thermostats, electronic locks,

etc. With the automation and remote capabilities built into M1 it is possible to control Z-Wave devices

from across the room or across the world. Benets include energy savings, convenience, and comfort.

• Operating Voltage: 12 Volts D.C.

• Current Draw: 31mA

• Housing: 4.25” x 6.375” x 2.125”

• Circuit Board: 2.75” x 3.95

NOTE: The Leviton VRC0P+3 is not included with the M1XSLZW.

It must be purchased separately. Specify Leviton Part Number:

VRC0P-1LW

• Activity/Status LED (Orange)

• Auto-Reset Hardware Watchdog Circuit

• Addressable (1-7) TYPE 5 Databus ID

• Connection to VRC0P-1LW: DB9M 9 Pin Port

• Connection to M1: Elevator Screw Terminals (4)

ELK-M1XSLZW

7 62158 55086 7

M1 to Lutron RadioRA 2 Interface

The M1XSLU is a dedicated M1 serial expander for connecting M1 Controls to a Lutron RadioRA 2 Main

Repeater. RadioRA 2 is a wireless multi-room control system for Lights, Shades, and HVAC Thermostats.

Interfacing a RadioRA 2 system to an M1 allows control in response to security system actions or

conditions. With the automation and remote capabilities built into M1 it is possible to control RadioRA

2 devices from across the room or across the world. Benets include energy savings, convenience, and

comfort.

• Operating Voltage: 12 Volts D.C.

• Current Draw: 31mA

• Housing Dimensions: 4.25” x 6.375” x 2.125”

• Circuit Board: 2.75” x 3.95”

• Activity/Status LED (Orange)

• Auto-Reset Hardware Watchdog Circuit

• Addressable (1-7) TYPE 5 Databus ID

• Connection to Main Repeater: RS-232 Cable

(included)

• Connection to M1: Elevator Screw Terminals (4)

ELK-M1XSLU

7 62158 55085 0

M1 16 Zone Input Expander

Adds 16 hardwired zones (with or without EOL resistor supervised) to the M1 Controls. Up to 12 may be

added, increasing the M1Gold to 208 and the M1EZ8 to 200 total zones (inputs)

• Operates from 4-wire data bus.

• Dip Switch address settings

• Flash Memory for rmware updating

• Plug-in terminal strips

• Status and diagnostic LED

• Operating Power Range: 9 to 14VDC

• Current Draw: 65mA

• Size: 6" x 3.25" x .75"

• Includes ELK-SWG for easy mounting in

ELK enclosure

ELK-M1XIN

7 62158 55017 1

M1 16 Output Expander, 8 Voltage & 8 Relays

Adds 16 outputs (8 voltage, 8 relays) to M1 Controls. Voltages can be used to trigger low current

devices (50 mA max. each). Operates from 4-wire data bus. Up to 12 output expanders may be used

for a total of 205 outputs. Option: convert 8 voltage outputs to relays using M1RB Relay Board.

• Operates on the 4 wire Data Bus

• Up to 12 Output Expanders may be added

• DIP Switch address settings

• Flash Memory for Firmware Updating

• Includes 12 conductor "Flying Lead"

Wire Harness

• Status LED with Diagnostic Display

• Relays: SPDT rated for 7A @ 28VDC,

10A @ 125 VAC.

• Voltage Outputs: 12VDC @ 50mA each

• Operating Power Range: 9 to 14VDC

• Current Draw 65mA Nom., 330 mA Max

• Size: 6" x 3.25" x .75"

• Includes ELK-SWG for easy mounting in

ELK enclosure

ELK-M1XOVR

7 62158 55019 5

M1 Relay Board, Plug-in

Used to convert the M1 Controls voltage outputs into SPDT relays.

• Relay Contact Ratings: 7A @ 28VDC,

10A @ 125VAC

•Wire harness length: 24”

• Current draw: 0mA idle, 250mA max

• Size: 6” x 3.25” x. 75”

• Provides 8 Relay Outputs

• Plugs directly into M1 Controls or

ELK-M1XOVR

• Includes ELK-SWG for easy mounting

in ELK enclosure

ELK-M1RB

7 62158 55008 9

NEW!!!

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 39 40

Kommentare zu diesen Handbüchern

Keine Kommentare

Clipsal 56011 Spezifikationen Seite 18

Kommentare zu diesen Handbüchern