Clipsal C-Bus Bedienerhandbuch Seite 127
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1250SM0904R10/09 C-Bus™ Basic Programming
10/2009 C-Bus™ Products Training Course
© 2009 Schneider Electric. All Rights Reserved. 121
Micro Function Action
Idle No action
Store 1 This stores the current level in the Recall 1 memory location (Blocks tab).
When the Recall 1 function is used, the group address reverts to this
level. The level is stored in non-volatile memory. No transmission is
made over the C-Bus Network.
Downcycle The output level is ramped down to minimum. If the output is already at
minimum, it ramps up to maximum. The Downcycle function should be
used in conjunction with the End Ramp function to ensure that ramping
ends at the desired level. The direction of output ramping changes with
each successive Downcycle/End Ramp operation. This allows a single
button to act as an up / down light dimmer. The Off Key function can be
used to terminate ramping if required. A RAMP TO LEVEL message is
transmitted over the C-Bus network.
Memory Toggle If the output is on, the Memory Toggle function stores the current level in
the Recall 2 memory location (Blocks tab) and switches the output off. If
the output is off, the function sets the output to the last level stored in the
Recall 2 memory location (the previous brightness level). An OFF or
RAMP TO LEVEL message is transmitted over the C-Bus network.
Down Key This function is similar to Downcycle except that it can only ramp the
output level downwards. The output will be ramped to the minimum level
unless either the End Ramp or Off Key function terminates the process
early. The ramp rate for the Down Key function is set by the Ramp 1
parameter (Global tab). The Down Key function has no effect if the
current output is in the off state. A RAMP TO LEVEL message is
transmitted over the C-Bus network.
Up Key The output level increases to the maximum level, unless either the End
Ramp or Off Key function ends the process early. The ramp rate for the
Up Key function is set by the Ramp 1 parameter (Global tab). If the
current level is already at a maximum, no action will occur. A RAMP TO
LEVEL message is transmitted over the C-Bus network.
Recall 1 The output level is set to the level stored in the Recall 1 memory location
(Blocks tab). A RAMP TO LEVEL message is transmitted over the C-Bus
network.
Recall 2 The output level is set to the level stored in the Recall 2 memory location
(Blocks tab). A RAMP TO LEVEL message is transmitted over the C-Bus
network.
Retrigger Timer The retrigger timer command starts the internal timer only if the output is
currently on (at any level). If the output is already on, the timer is
restarted. A RAMP TO LEVEL message is transmitted over the C-Bus
network.
Start The internal timer is started without affecting the output level (if the timer
value is greater than zero). An ON message may be transmitted over the
C-Bus network.
Ramp Off The output level is ramped to the minimum level and then switched off.
The ramp rate is set by the Ramp 2 parameter (Global tab). This function
cannot be interrupted by the End Ramp function. A RAMP TO LEVEL
message is transmitted over the C-Bus network.
Ramp Recall 1 The output level is ramped up or down (depending on the current level),
to the level stored in the Recall 1 memory location (Blocks tab). The
ramp rate is set by the Ramp 2 parameter (Global tab). This function
cannot be interrupted by the End Ramp function. A RAMP TO LEVEL
message is transmitted over the C-Bus network.
- Basic Programming 1
- Products Training Course 1
- Please Note 3
- Class B FCC Statement 3
- Safety Precautions 4
- Clipsal Introduction 7
- What Is C-Bus? 8
- Why Use C-Bus? 9
- Functionality 10
- Simple Wiring 10
- C-Bus Principles 13
- C-Bus Power Supply 14
- PC Interface 14
- Network Bridges 15
- Input Units 16
- C-Bus Wall Switches 17
- C-Bus Sensors 18
- Miscellaneous Inputs 20
- Output Units 21
- C-Bus Dimmers 23
- Maximum Load Calculations 25
- Fluorescent Dimming 27
- IR Transmitter 28
- Software 29
- C-Bus Cable 30
- Cable Current 31
- Cable Terminations 31
- 1 2 3 4 5 6 7 8 32
- Cable Topologies 33
- C-Bus Units 36
- C-Bus Voltage 37
- Power Supply Placement 38
- 1 km of C-Bus Cable 39
- Over Voltage Protection 40
- C-Bus Current 41
- C-Bus Current Consumption 42
- C-Bus Clock 43
- Network Burdens 44
- Mains Segregation 45
- Learn Mode 47
- Selecting Output Channels 48
- Learn Mode Operations 49
- Timer Configurations 50
- Super Learn Mode 51
- C-Bus Addressing 53
- C-Bus Toolkit 54
- 5500NB 5500NB 5500NB 5500NB 54
- Network Address 56
- Network 254 56
- Network 253 56
- Group Address 001 60
- Group Address 002 60
- Group Address 003 60
- Group Address 004 60
- Group Address 01 61
- C-Bus Tags 62
- How C-Bus Works 63
- L5504D2U 65
- L5504RVF 65
- 5084NL 5082NL 65
- C-Bus Message Types 66
- Status Report Interval 66
- C-Bus Into to Toolkit 67
- C-Bus Toolkit Overview 68
- The C-Gate Console 69
- The Toolkit Main Menu 70
- The Navigation Tree 71
- The Toolbar 73
- Installing USB Drivers 80
- Creating a Project 80
- Editing a Network 82
- Creating Group Addresses 83
- Add Units to Database 84
- Adding Units Manually 85
- Scanning a Network 90
- Readdressing C-Bus Units 92
- Serial Number Readdress 94
- Application Log 96
- Programming C-Bus Units 97
- DIN Rail Relays 98
- Channel 1 101
- Logic Group 101
- Channel 2 101
- Turn On Tab 102
- Recovery Tab 103
- Restrike Delay Tab 104
- Global Tab 105
- Status Tab 106
- DIN Rail Dimmers 107
- Logic Tab 108
- Min/Max Tab 112
- Dual Applications 117
- Indicators 119
- Disable All Keys 121
- Corridor Linking 123
- Timing Parameters 123
- Micro Functions 125
- Passive Infrared Sensors 128
- PIR Function Details 129
- Sensor Enable/Disable 130
- False Triggering Sensors 130
- Light Level Sensors 131
- Remote Triggering Scenes 136
- Variants 141
- Labelling Scenes 142
- C-Bus Diagnostics 143
- Analysis Tools 144
- Multimeter 145
- Oscilloscope 146
- Diagnostic Utility 146
- Diagnostic Utility Setup 147
- Support and Training 148
Verwandte Produkte und Handbücher für Touchscreen-Monitore Clipsal C-Bus
Touchscreen-Monitore Clipsal C-Bus2 Spezifikationen
(120 Seiten)
(120 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.888 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern